A "3-inch" RV drain pipe doesn't measure 3 inches across the outside. On standard Schedule 40 ABS or PVC drain pipe, the size is a nominal name: 3-inch pipe measures about 3-1/2 inches in outside diameter, and 1-1/2-inch pipe about 1.9 inches. That gap is why a replacement waste valve is chosen in two steps: confirm the nominal size from the pipe itself, then match the way each end of the valve connects, because a valve of the right size with the wrong ends still won't go in.
Before You Measure Anything
Work on a tank that has already been emptied and rinsed, with its valve closed and the outlet capped. Wear disposable gloves and eye protection, keep a bucket under the outlet, and wash your hands thoroughly afterward; anything that drips here is wastewater.
Then look at each tank's outlet separately. The black and gray tank lines on the same RV can be different sizes, so a size you confirm on one pipe doesn't carry over to the other.
Reading the Nominal Size From the Pipe
Measure across the outside of the pipe just upstream of the valve. A reading near 3-1/2 inches points to nominal 3-inch pipe; a reading near 1.9 inches points to nominal 1-1/2-inch. If the pipe sits too close to the frame to measure, markings on the old valve or the RV maker's documentation can confirm it. The bayonet outlet you twist a sewer hose onto is a 3-inch fitting (the Camco Camper/RV Gate Valve listing describes four bayonet prongs for 3-inch sewer fittings), but a smaller line can join the main line upstream, so the outlet alone doesn't tell you a gray-tank valve's size.
Write the size down per tank. Waste valves, valve bodies and seal kits in this collection are listed separately for 3-inch and 1-1/2-inch, and the two are not interchangeable.
Matching the Ends, Not Just the Size
Once the size is settled, look at how your current valve attaches on each side.
| Connection | What you see | How it joins | Example from the listings |
|---|---|---|---|
| Valve body between flanges | A slim gate housing bolted between two flanged ends | Bolts and seals; the pipe-side ends stay in place | Valterra T1001VPM 1-1/2" body states it includes seals, nuts and bolts |
| Hub | A socket the pipe slides into | Solvent cement suited to the pipe material, per the valve's instructions | 3-Inch Hub to 3-Inch Lug valve states its hub glues onto 3" PVC sewer pipe |
| Lug / bayonet outlet | Prongs or lugs at the open end | A sewer hose fitting or cap twists on | Camco gate valve describes four bayonet prongs for 3-inch fittings |
If the old valve's ends are bolted flanges and they're sound, a replacement body can be the smaller job, since the glued joints stay untouched. The Valterra T1001VPM Bladex 1-1/2" Waste Valve Body listing states a 1-1/2" valve size, use with GrenTec, Bladex, Valterra, Bristol and Anonda valves, and included seals, nuts and bolts. Confirm your existing valve is one of those designs before ordering it.
When Cement Is Involved
A hub connection means cutting and gluing. ABS and PVC take different cements, so check what your RV's pipe is made of and follow the valve's own instructions for the cement and cure time, working with ventilation and away from any flame. If the pipe is cracked near the tank, or the joint sits where you can't cut and glue cleanly, an RV service shop is a better choice than forcing a fit.
A Few Things People Ask
Q: Can one valve body work on both my black and gray tanks?
Only if both outlets are the same nominal size and the same valve design; measure each pipe separately before ordering.
Q: Does a valve body come with new seals?
Some do; the T1001VPM listing states it includes seals, nuts and bolts. Check each listing's contents line rather than assuming.
Getting Both Ends Right
Browse Plumbing with each tank's size and connection type written down, and compare every listing's stated size and fit.
- Empty and rinse the tank first, and wear gloves and eye protection
- Measure each pipe's outside diameter: about 3-1/2 inches for 3-inch, about 1.9 inches for 1-1/2-inch
- Note whether each end is a bolted flange, a glued hub or a bayonet outlet
- Prefer a matching valve body when the flanged ends are sound
- Use the cement the valve's instructions call for, matched to ABS or PVC pipe, with ventilation and no flame nearby
- Confirm your valve's brand and 1-1/2" size against the T1001VPM listing before ordering that body
The right waste valve starts with the pipe, not the package: confirm the nominal size by measuring, then match how each end joins. Handle each tank's outlet on its own terms, and keep gloves on and the tank empty until every new joint has been checked for leaks.